Support us on Patreon: https://www.patreon.com/woodshoplife
Guys Questions:
1) Would also like to get either an Incra Miter Sled or Miter Gauge. I see they have a sled/gauge combo or a sled with an integral miter gauge. Can you discuss the pros and cons of each option? - David
2) For Router table use is there really a difference when using a pattern bit vs a flush-trim bit when you want to flush an edge up with a template? Does riding the bearing on top vs on the bottom cause any safety concern? Does one leave a better/worse edge or does it even matter? Thanks, Ryan
Seans Questions:
1) Hey guys, love the podcast. Especially listening to guy, because I feel like I'm listening to myself from the future. In response to your recent call for more questions, I have one about tool sharpening. Specifically, what kind of honing jig to buy. I see there are a lot of them out there, but do you have any recommendations on a specific one to get. I'm getting into more hand tool work, and I want to be able to maintain my own chisels, as well as restore some old hand planes that I have. Any advice you may have is much appreciated. Thanks again for being willing to share your knowledge and experience. -Tavis
2) You've mentioned some of the books you've relied on, and I appreciate that, since I'm a green-as-grass beginner, and benefit from any source of information I can get. I'd also like to hear you talk about what mentors or teachers you had who helped shape your skills. Have any of you taken formal classes or gone to woodworking schools? I know that the best way to develop skills is by building furniture and learning from mistakes, but I also hope to participate in a class sometime, if only to find an active woodworking community. - Martin
Huys Questions:
1) I've recently bought a good planer/jointer combo machine. It uses 3 planer knives in the cutter block. I won't be using it enough to consider an upgrade to some sort of helical cutterhead. So I've been thinking about a practical way to sharpen the knives. I've come to a jig, some sort of wooden block with an insert for one knife. The top surface of the block is tilted in such a way that my water stones have support for the correct angle when I use them to sharpen the edge.The jig works, but I wonder if there is a more practical (faster) way to sharpen. I see that Tormek sells a sharpening system that does this, but since it costs more than the helical cutter block, I find that too expensive.My question: do you know of an affordable sharpening system for planer knives (mine are 10" long)? - Bart
2) Looking at finishing the top I was going to use epiphanies spar varnish but was wary of using this finish because of UV resistance. Would this inhibit the natural darkening of Cherry? My other option was General finishes ARM R seal or Waterlox. I don’t have way to spray so conversion varnish is out of the question.
My other thought was to dye the slab with Lye and use the Epifanes.
Keep up the good work.
ThanksJesseBeechland Furniture
 
Social Picks
Guy: @kingposttimberworks
Sean: @hawthorne_fine_boxes
Huy: @affinecreations

Episode 25 - Flush Trim Bits, Mentors, Sharpening Jointer Knives, and MUCH More!

Bi-Weekly Podcast Focused on the Craft of Woodworking

Education

Training

Language Courses

Higher Education

K-12

Educational Technology

How To

This Episode's Questions:
Brian's Questions:
Gentlemen,First, I hope you all know that the sounds that pop through occasionally from your families in the background don't make a bad podcast; they make you human and THAT is part of what makes your podcast great.On the subject of families, I have 3 young sons (6, 4, 2 years old) that love "helping" with woodworking projects and learning about tools.  The family has outgrown our current dinner table, and I've been tasked with building a new one.  I'm planning a 6.5'x3.5' dinner table that doesn't need to be an showpiece heirloom dining table, but I'd love to produce something that will look nice and can handle the inevitable mayhem of a young family.   Can you recommend a wood species and some finish options that will stand up to these demands? I can feel white oak calling me here, should I answer the call?  (For context, our kitchen cabinets and floors are all darker wood tones so more dark might just blend into the background too much.)Thank you as always for your contribution to the woodworking community.  Your knowledge, experience, and unique characters make this truly the best woodworking podcast. Evan
Hey guys! Love the podcast and appreciate all the work you put into it. My wife and I have been planning a remodel of our kitchen for a few years. I really want to build the cabinets, but also recognize that my time is pretty limited with work, and my wife doesn't want a partially completed kitchen for months. I'm currently designing the kitchen in Sketchup to a pretty high level of detail because we have some restrictions with the space that I need to ensure I take into account. The goal is to work through as much as I can in Sketchup to reduce guesswork, decisions, and time once I start  building.
We have currently decided that I will build the cabinet boxes and face-frames since it will be easer to custom design and build for the space, and I'm researching options for outsourcing the drawer boxes and drawer/door fronts. We are planning on using rift sawn white oak with inset door and drawer fronts.
The drawer boxes seem like a pretty easy option to outsource, but the fronts seem like they could pose some challenges that I may not be considering. Should I be worried about significant color or grain differences between the outsourced supplier, and what I can get locally to build the face-frames?Since they will be inset, do you have a recommendation on sizing when I order? For example, I'm planning on a 3/32" reveal between the face-frame and doors/drawers, should I order with 1/16" or the full 3/32" oversized so I can trim to the exact opening once the cabinets are installed in case something shifts?Thanks for the help! Jason
Guy's Questions:
Hi guys. Love the podcast! Wish I could find a fishing podcast as good. Life would be perfect.I made the move to a Fuji Sprayer.  I bought one with the gravity feed gun but now think I made a mistake. I think it would be easier to hold finish in the cup between coats.What is your preference and why?Thanks so much. Joe
Hi Guys,
I recently asked a question concerning how to glue up a frame and panel so it’s flat. I took your advice and it worked great. Thanks so much!!!I have two unrelated questions:I recently purchased expensive hinges from Horton-brasses. When I received the hinges I made a jig out of MDF so I could simply rout out the mortises for the hinges to sit in. As usual, I make the jig so they are a perfect fit for the hing. I tested the jig on a piece of scrap and the hinge fit perfectly. I then used the jig on a cabinet I made and the hinge did not fit. I tried the various hinges I purchased and only one of the hinges fit (the hinge I used to make and test the jig). After measuring the hinges, I discovered that they were all different sizes varying by about .01”. I contacted Horton-brasses and explained the problem and they told me that their acceptable tolerance is +/- .05”. With some simple math this means that

Durable Kitchen Table, Hinge Wierdness, Sanding Slabs and MORE

This Episodes Questions:
Brian's Questions:
Hey guys I have a kinda lengthy question, so new to woodworking and I’ve been listening to your guys podcast and really like it!! Very helpful! Question #1 is it better to have a good table saw blade over a good saw #2 is it better to have a good table saw over a good incra fence!? Back story I have a delta table saw, I got for free from a friend, I was wondering if it’s worth spending the money or save and eventually get a better saw like a powermatic table saw etc.maybe I get caught up in the details of tools and expect them to do the work for me, but I am someone that like to have the right tools for the job. Granted as new as I am it’s hard to justify $10,000 to have all the right tools, just wondering if I should focus more on making something then, on the tools! Hope it all makes sense and it’s not more of a rant!! Thank you for all the work you guys do!! Ivan
I'm making a mantle for my living room out of rift-sawn white oak plywood. 74" long, with a miter fold design. My wife wants it to look the same way it does before applying finish, and I'm not sure how to do that or if it is even possible. I've tested with water-based poly (Minwax), but it causes it to look a bit "golden". Suggestions? Brian
Guy's Questions:
Hi fellas,Love the podcast and all your great advice.I recently glued up a free-standing (liquor) cabinet and was very nervous about it being square, especially since it was difficult to check for square (measuring corner to corner in the front and back) with all the various clamps on.  I ended up making the back panel (which fits into rabbets), which I knew was square, and placed it in the back (without glue) while the glue dried on the various joints (through tenons on top and bottom shelves, mid-shelves sit in stopped dados).  The idea was that if the square back panel fit correctly, it would help pull the whole cabinet into square. 
It turned out perfectly this time (wahoo!), but am not sure if I got lucky or if this is a reliable method to come back to.  What do y'all think?  Does this method make sense?  Any other suggestions on how to check or ensure square with free-standing cabinets of a decent size (46" tall, 26" wide, 16" deep)?Thanks, Bryan
Hi gents:  long time listener here and as I’ve said before, thanks so much for the great content you deliver.  You have discussed your spraying equipment set up in the past but I was hoping you could describe your spray BOOTH set up- obviously Brian is exempt from this question since he doesn’t apply finish.  How do you guys spray volatile finishes in the winter on your garage?  Do you have a spray booth like set up?  Do you openly spray in your garage workshops?  How do you vent potentially dangerous fumes?  Any details you can provide would be appreciated as I would like to do more spraying of shellac and I like wipe on poly both of which are challenges in winter time when you can’t work outside.Liam from Indianapolis
Huy's Questions:
I’ve recently found the podcast and am loving going back and learning from each episode! I’ve noticed that a ton of time has been dedicated to doling out wisdom on different types of finishing techniques and products. I’m sure the best way to learn all of this is through experience, but do you have and resources to recommend budding woodworkers as a go-to guide? With the way my brain works, learning the origins of each finish, their make-ups, and how that brings about their use cases and strengths/weaknesses would go a long way for me to internalize all of the various do’s and dont’s. Do you have a resource you go to when considering applicable finishing materials on a new project? Jeremiah
Love the show, I appreciate you guys giving it the time it takes to make it happen. My question is about a solid Walnut table that I built for my eat in kitchen. The material was 30yr + air dried Walnut milled down to a thickness of about 15/16" for the table top each board is six to eight

Water White Finish?, Gluing Up Square, Sagging Table Top and MORE!!

This Episodes Questions:
Brians Questions:
Hi guys! Love the podcast, as always. My question for you guys this time is about design. Specifically, it's about design based on that "special" piece of lumber. For example, I purchased a large piece of mahogany in the late 1990's to build electric guitars. I made two guitars from it and was left with a chunk of beautiful lumber that traveled with me for the next 25 years. Two years ago, I bought a mid-sized slab of black locust. I don't make "slab" furniture or use copious amounts of epoxy, so it'll end up getting cut up into a project.I know you guys normally design your projects and then buy the lumber, but have you ever bought (or acquired) that unique board and then had to design a project to do it justice? If so, what was the project? As a follow up question, what is the longest that you have ever owned a piece of lumber that you just couldn't get rid of?
Thanks,  Joshua from The Black Dog Woodworks.
I'm a new listener and your podcast has been a blast to listen to on my evening runs. I just finished a 3-year, gut-to-the-studs home renovation, and my 1 car garage was the renovation workshop. Now that the home is finished I am transitioning the shop into a proper woodworking space. During construction, I used a lot of 16D nails and 3" construction screws and tried to have a variety of fasteners on hand so I wouldn't be running to the hardware store 3 times a day.
This got me thinking. What are some common fasteners you like to keep in your shop? Any common screw sizes? Bolts? Washers? Nuts? Nails? Staples? It seems in woodworking shops that there's always a balance between having so many supplies that you'll never use most of them in 10 years to having so few supplies that you'll be running to the store 5 times a day. What is your approach to hardware consumables? Thanks for the great podcast. Adam
Guys Questions:
Really appreciate the podcast, i have been listening for about 18 months and am also working through your previous podcasts.   I am starting the dive into spray finishing. I have previously used wipe on or brush on finishes. I like shellac, but often coat with wipe on poly for extra protection. I would picture doing the same going forward.  Question: What are considerations/benefits to using a water based conversion varnish over wb poly?  What type of ppe is appropriate?  I have a relatively large shop which is climate controlled, not attached to house and can set up an area for finishing when needed, what type ventilation would be desirable for occasional finishing in this situation?  I build furniture and smaller items. Thanks,David at xcuse4tools custom woodwork    Hello everyone. Love the show. Great dynamic between you all and I really enjoy the lack of ego in the question answering. Your answers are efficient, helpful and easily digestible to a beginner woodworker.I recently acquired a Jessem Pocket Mill Pro for loose tenon joints. Like many, I had lusted after a Festool Domino but couldn’t justify the price tag for a hobby shop. The Pocket Mill Pro is a fraction of the cost and does everything I need it to do for my projects.The workstation that pairs with the pocket mill pro can also accept Jessem’s dowel jig. My question to you all is would a dowel jig even be necessary when I have the ability to make loose tenon joints already? Is there any advantage to adding the dowl jig to my arsenal or is it a waste of money when I already have the Pocket Mill Pro?Thanks in advance for any insight. Jason
Huys Questions:
I'm planning on making a face grain chess board.  I'll use 3/4" MDF as my core and glue the chess squares on top (grain from all squares facing same direction).  Chess squares will be about 1/8" thick.  I assume I'll also need to glue some 1/8" wood on the bottom to balance out the stresses.  I'll orient the bottom grain in the same direction as the top.  My question is, do I need to glue both sides at the same time, or can I glue one side, le

Common Fasteners, Dowels vs Dominos, Hand Plane or Sand Paper and MORE!!

This Episodes Questions:
Brians Questions
I have a question for you about glueing up table aprons. And I’m mostly referring to large dining tables. The aprons I’m making are generally w 8/4 stock roughly 4” width. I can manage to get the legs and the aprons milled and cut square. All my joinery is w dominoes. Whenever I do the glue up everything is slightly out out square despite everything being square prior to glue up . I have pipe clamps and parallel clamps and have tried both. For some reason I can’t get the clamping pressure or positioning right. Any tips would be appreciated. Bryan
Hello everyone,Wanted your advice on dados and what I may be doing wrong. When I cut the dado and mating piece I make sure to get a good tight fit during the dry fit. My issue comes up when I'm sanding. I'll take all the pieces apart and sand them to the desired sand grit (180 or 220 depending on finish). But when I go to glue up my mating piece is now loose in the dado. Should I be making the dado smaller, should I just wait to sand till it's all glued up or do you have any other advice?
Thanks,Paul at Twin Lakes Workshop
Guys Questions
I have listened to all your podcasts and have very much enjoyed and learned from them. I listen to primarily three woodworking podcasts and Woodshop Life is far and away the best.
I have to confess I am a wood hoarder. I do a lot of small projects (scroll saw, boxes, and the like) and end up with small pieces left over that should be good for something. But how do I organize them and what size is too small, in your opinion, to be useful? The same applies to pieces left over after building furniture or other large projects? Do I just throw everything in the burn pile or is there a logical way to sort and store small pieces of lumber?
And one small criticism: need to update the website with Brian’s information since he is officially part of the podcast. Roger Martin
Hey there fellas! I’m with a small furniture and cabinet shop called Silt Studio in Atlanta. Love the podcast and the great wealth of knowledge you guys bring to the world of woodworking. Guy, don’t let anybody tell you you’re wrong, they’re never right. I have a question about the relevance of our table saw. It’s a Powermatic PM2000 (I know guy loves his)with a 5x5 outfeed and a 36” rail extension. It’s really been a great workhorse for our shop. The space is about 3000 sq ft and we are quickly outgrowing the footprint for the amount of kitchen and cabinet jobs we’re taking on. There are also columns on a 9’x 14’ grid pattern so the space isn’t wide open.  We’re talking about getting a large slider to facilitate speedier and more accurate square cuts. Currently we’re ripping down sheetgoods with our festool track saw then finishing on the table saw. If we get a slider, a large chunk of our milling/cutting space would be taken up. Is it worth keeping the powermatic and just losing the outfeed to save space  or can we do everything we need to on the slider? We’re considering the laguna 12/8 model slider. Looking forward to your thoughts! Thanks so much, Sam
Huy's Questions:
Hello gentlemen.Great woodworking podcast. I am in the market for a drum sander. Currently I have a Jet 22-44. It is a love/hate relationship with all the known issues. The budget would be around 2,000-3,000. I was thinking arbor open ended powermatic 22-44 o it would be better to get Grizzly 24 or 24, or something similar that is closed ended. Also would you recommend single or double. What about finding bigger 37” or a similar from shops liquidations. I know there is wiring and things like that. I have a hobby workshop with some 220 equipment. Like I mentioned it is a hobby now maybe it will grow may it will not. I originally got the openeded sander hoping that I can send wider boards (stupidly table tops) but obviously it is not as easy as it would seems to be. I do not know if that helped on made my question more murky. Sometimes there a good deals on Facebook Marke

Clamping Pressure, Wood Hoarding, Iron and White Oak

This Episodes Questions:
Brian's Questions:
Hi guys.Long term listener. Great pod cast.I recent have a gotten my first 220 table saw. Grizzly 690. It works great and my router table, wood pecker P2.I have a small shop and space always is tight.I am thinking about buying an infra table fence with the router attachment as I can put it off to one side as my cut requirements are less than 24 inches. Mainly 12-18 inches wide as my happy space is projects within 2 ft by 4 ft.Anything larger is handled on my Yeti Smart bench, 4x8 cutting capacity.Guy is a big fan of incra tools and I just wonder if his opinion on what is best . Replace a good table saw fence with the incra one that was mentioned before and an added router table attachment or keep things separate?What is your opinions?Thanks for helping out and making 8 quarter effort to help.  Or 200% Paul Mitchell
First off, I really enjoy the podcast. I am a hobbyist woodworker who loves to build custom cornhole boards.I have built some simple furniture like a coffee table using custom metal legs. I would like to make some simple wooden boxes for my adult daughters. I am think about trying box joints for my first attempt.I have most of what I need to do this project but I don't own any chisels to clean up my work. Can you suggest a brand or set that would be affordable yet good quality that could last for future projects? Also, how easy is it to maintain the edges? Should I plan on sharpening them myself or send them out to a pro?ThanksJohn in Ohio
Guy's Questions:
Great show, I’ve asked a few questions over the years and you always have great advice.I’m having problems when I glue up frame and panels for doors on cabinets and keeping the frame flat. This problem is exacerbated when there are two doors and they are both not flat. My joinery is square, the styles and rails and panel are all square and flat, so I know that’s not my problem.  I’m am guessing that it’s the way I’m clamping it during glue up.  I would appreciate any thought on what I may be doing wrong, or tips and techniques you use when gluing up panels.Thanks for the help and keep up the great work!! Mike Gitberg
Could you give an explanation of your general setup and process for finishing regarding the consumables.  I feel like I am not very efficient and am wasteful during this process. For example, I just finished a shaker end table that I put a sealcoat of shellac on, and followed that with a hard wax oil. It came out looking great but I feel like there is a huge mess to cleanup after. Because of the risk of the oil self-igniting, I laid everything on my garage floor after I was done, so it could to dry.  I see that I used 8 rubber gloves, a dozen shop towels, scotch brite pads, several sheets of butcher paper and the mixing cup for the oil. Also, can I reuse the mixing cup from the hard wax oil? How would you clean out the leftover mix? Thanks for the great podcast! Jeff Hughes
Huy's Questions:
Hey guys, I’ve sent in questions before and always got great responses, but I have a strange one for you today.I’m a teacher, and a bit of an eclectic one. I like to keep my kids on their toes wondering about me. I’ve always wanted to make a throne to keep in the room for me to lecture from, or to let kids sit on. I teach high school, so the kids are full human sized mostly and never careful, so well built is a necessity. Again, I’m a teacher, so budget friendly design is also a consideration. I have some recycled 3” square cedar posts, and other scrap, but I definitely can’t afford to go out and get 4” thick white oak or walnut. I am also a leather worker, so incorporating leather seats or whatnot is within my skills. Not afraid of carving or painting for details.I’ve done some looking for inspiration and it just doesn’t seem folks are building thrones all that often. The only chair I’ve built is an Adirondack from plans. Any ideas, thoughts, recommendations, resources, donations? I’d especially like to at le

Episode 25 - Flush Trim Bits, Mentors, Sharpening Jointer Knives, and MUCH More!

Download our free app to listen on your phone