Support us on Patreon: https://www.patreon.com/woodshoplife
 
Sean
1)Hey fellas. 2 questions for you
 Purely hypothetical- you can only have 1: table saw or track saw. And why?
 When sanding back, how far is back? Are you aiming for a perfectly flat surface? This is harder to achieve on open grain woods like oak, yes?
Keep up the great show. Mark Aka Matt
2)I am finishing a large table, 10'x 5', and would like to use Shellac on it, then seal it with water based poly, specifically General Finishes High Performance Water based Satin.
 How important is it to keep a wet edge with the shellac? Since it dries so quickly, I can see some difficulty keeping a wet edge on a piece this big. If so, any advice on how to do that?
 On a test piece I've been using, the above mentioned poly is drying FAST. As in completely tack free in under 10 minutes. I'm working indoors in Central Ohio, with temp about 68, and low relative humidity, probably around 35-40%. Should I be concerned that the Poly is drying that fast? Will it cause any problems?
Thanks  and keep up with the great show!
MLBett WoodWorks
 
Huy
1) Good morning. I have a quick question about building a slab top hand tool bench. I was recently gifted a great 60”x20”x4.5” oak slab. I’ve read Chris’s book and would like to do a roubo style bench. My problem is my current shop is in the basement and I would eventually like to move to a new outbuilding shop down the road. What design ideas would you suggest for a sturdy base design that is functional but could eventually be broke down and moved them out back together? I was thinking sliding dovetails in the bottom of the slab then build a base to connect to that? I have no idea. 

Episode 67 – Shellac Tips For Large Surfaces, Starting Clamp Collection, Break Down Workbench, & MUCH More!

Bi-Weekly Podcast Focused on the Craft of Woodworking

Education

Training

Language Courses

Higher Education

K-12

Educational Technology

How To

This Episodes Questions:
Guy's Questions:
With mothers day around the corner, I plan on knocking out a couple of small jewelry boxes. Mitered corners and book matched grain for a seamless look. 2 questions leading into this project. The first is more likely for Guy.
In the past my boxes have been cut to 45.1 degrees to ensure a closed outside corner. My table saw is a jobsite saw and setting a precise angle is extremely difficult. I recently set up a router table and have seen guy use a 45 degree chamfer bit to cut miters this way. How close to 45 degree do these bits actually get? Is there a brand you recommend for better accuracy? How bad is the tear out?
2nd question. In the past I used a wiping poly to finish the boxes. However VOC's are a concern for these boxes. I'd like to finish the boxes with a base coat of shellac and finish with beeswax top coat. I purchased a block of beeswax but didn't really think about how to dissolve it for quick finish. Seems like mineral spirits are the leading candidate but I'm curious if anyone has used natural oil citrus solvent for the same task (I'd likely by the version from milk paint company). Jose
Gentlemen, thank you for all you do to support and educate the woodworking community through this podcast and other platforms.  I'm planning out a full kitchen remodel for our home and will be building the cabinets myself.  The style of cabinets will be frameless/euro style which means all the plywood will need to be edge banded.  The plywood will be pre-finished, but the doors and drawer fronts will be painted.  How would you recommend finishing the edge banding to match the door and drawer front color?  Would you do hardwood edge banding and paint it?  That seems like it would take a lot of taping which leaves room for lots of error.  Is there such a thing as custom colored edge banding for cabinets that is either iron-on or peel-and-stick?  I don't have an edge banding machine so that probably limits my options.  Thanks in advance for your help! Joel
Hi guys,Thanks for providing some great knowledge for fellow woodworkers.My question is around drum sanders and the usefulness of them in a hobby shop. When do you use a drum sander and what type of projects are you using a drum sander on?I just purchased a 20” bandsaw and would like to start resawing veneers for projects. In the past I would buy 1/16” thick veneers from a commercial veneer shop which worked well. But I question if a drum sander is actually required/desired  for this operation. I’ve read a bunch about troubles with drum sander’s and really question if it speeds up the work.Could I just joint a fresh face, resaw. Then joint another fresh face and so on. Then glue up the panel. And either clean up the panel on the planner or ROS?In my  future I probably have a set of kitchen cabinets and various built in cabinets(which I would either buy plywood or use commercial veneer and glue my own). I normally make freestanding furniture as well. This isn’t a production shop, and I have all the normal tools for dimensioning lumber, TS, Jointer, and planer.Feel free to summarize my question, just wanted to give you guys enough context.Thanks,Jesse Beechland Furniture
Huys Questions:
Hi GuysHave known of & liked Guy’s YT channel for a number of years and recently came across this podcast which I’m really enjoying as I go through the back catalogue.I must be on similar wavelength to you Guy as I love (& own a lot / most of) the Incra stuff, saw your MFT style outfeed which I’m about to build a copycat of (just awaiting delivery of the aluminium extrusion) and am in the midst of milling the timber to start building your mini workbench, the plans for which I recently bought.I then happened on your YT channel the other day Huy and whilst watching the 6yo shop tour video was interested to see your boom arm. Could you tell me a bit more about it. Is it bought as is, or built up from tubing etc?Keep up the good work.Thanks Andy

45 Deg Corners, Making Veneer, Clamping Pressure and MORE!!

This Episodes Questions:
Brian's Questions:
I'm so curious about the Laguna bandsaws that Guy used at work. Long time listeners of this podcast could easily believe that Laguna bandsaw tables are at knee height and unusable. But I have a Laguna 14/12 and the table is at 35", which seems really normal, and I'm pretty tall. All the other Laguna saws I've used or been around seem about in the same range. Is this not normal? Is Guy freakishly tall? Or an advocate of chest height bandsaw tables? Parker
I haven't felt like my woodworking really justifies a jointer yet.  I don't generally mind using a planer sled to get flat faces and a jointer sled on the table saw to edge joint boards, but I've never tried to use those workarounds on long stock (over 4'.)  With that being said, this dinner table project that is looming ahead of me seems like it might be the moment to finally take the plunge and buy a jointer. Do you think its possible to get the table top glue-ready without a jointer? I trust my planer sled to get flat faces, but I'm wondering if you think edge jointing such long boards is possible with an extra long table saw jointer sled jig.  Any tips on milling and glue up for this table top would be very appreciated. 
Part 2: Or maybe you guys can give me the nudge to consider this dinner table project as the moment to finally buy a jointer.  I suspect that a bench top jointer wouldn't give me much (other than efficiency) over the work arounds that I already use for milling.  Do you have any recommendations for a first jointer? I don't have major space limitations but I do like to save money, so I'm curious if you guys would send a case like mine to scour craigslist or facebook marketplace for an old delta 6".
Thanks as always for your contributions to the woodworking community!  It can't be said too often: you guys really do make the best woodworking podcast there is!! Evan
Guys Questions:
Hey guys, I’m new to woodworking, really enjoying listening to the podcast!! I have a question, would you guys be able to go over what you use your 3/4, 4/4 etc lumber!? I often think that you need thick lumber for projects. I don’t have a project in mind but I bought some rough saw lumber that I plan on using for trim in the house but I bought enough to have plenty left over. Ivan
I want to build a cherry coffee table for my house. We've got a couple of cherry pieces that I've made. I really love watching them darken and get more beautiful with age. The other pieces I've made don't really see much direct blasting sunlight so the process is subtle. The coffee table however, would get some direct morning sunlight every day (or at least for the three months of the year that we get direct sunlight in the pacific northwest). I'm worried about uneven color change and sun shadows on the top where there would be decorative objects or books or things left in one spot for a period. If I pre-darken it by leaving it in the sun for some hours or a day or two will that slow the process enough to alleviate this? If so, should I do it before or after finishing? Is there anything else I can do to help, besides not putting stuff on top of course? Parker
Huys Questions:
Hi Fellas, I recently purchased a horizontal crown bit ( ref: Yonico 16172 ) to apply a soft dimple to the drawer faces on my tool cabinet. I will be recessing the drawer pulls within them.The challenge that I'm facing is that the drawer faces are a little small, 5 1/2" x 3 1/4", and without being overly creative on work holding, I'm not seeing a safe way to plunge the face onto the bit in my router table, or plunge the bit into the face with a hand held router.My plan is to chuck the bit into my drill press and use that to apply the cut.  What experience, tips, or words of advice might you have in using a drill press with router bits? I have a Grizzly G7943 which only spins up to 3050 rpm.Thanks in advance, and for all that you guys do for our craft of woodworking!Justin
I have a

Bandsaw Height, Darkening Cherry, Drill Press or Router? and MORE!!!

This Episode's Questions:
Brian's Questions:
Gentlemen,First, I hope you all know that the sounds that pop through occasionally from your families in the background don't make a bad podcast; they make you human and THAT is part of what makes your podcast great.On the subject of families, I have 3 young sons (6, 4, 2 years old) that love "helping" with woodworking projects and learning about tools.  The family has outgrown our current dinner table, and I've been tasked with building a new one.  I'm planning a 6.5'x3.5' dinner table that doesn't need to be an showpiece heirloom dining table, but I'd love to produce something that will look nice and can handle the inevitable mayhem of a young family.   Can you recommend a wood species and some finish options that will stand up to these demands? I can feel white oak calling me here, should I answer the call?  (For context, our kitchen cabinets and floors are all darker wood tones so more dark might just blend into the background too much.)Thank you as always for your contribution to the woodworking community.  Your knowledge, experience, and unique characters make this truly the best woodworking podcast. Evan
Hey guys! Love the podcast and appreciate all the work you put into it. My wife and I have been planning a remodel of our kitchen for a few years. I really want to build the cabinets, but also recognize that my time is pretty limited with work, and my wife doesn't want a partially completed kitchen for months. I'm currently designing the kitchen in Sketchup to a pretty high level of detail because we have some restrictions with the space that I need to ensure I take into account. The goal is to work through as much as I can in Sketchup to reduce guesswork, decisions, and time once I start  building.
We have currently decided that I will build the cabinet boxes and face-frames since it will be easer to custom design and build for the space, and I'm researching options for outsourcing the drawer boxes and drawer/door fronts. We are planning on using rift sawn white oak with inset door and drawer fronts.
The drawer boxes seem like a pretty easy option to outsource, but the fronts seem like they could pose some challenges that I may not be considering. Should I be worried about significant color or grain differences between the outsourced supplier, and what I can get locally to build the face-frames?Since they will be inset, do you have a recommendation on sizing when I order? For example, I'm planning on a 3/32" reveal between the face-frame and doors/drawers, should I order with 1/16" or the full 3/32" oversized so I can trim to the exact opening once the cabinets are installed in case something shifts?Thanks for the help! Jason
Guy's Questions:
Hi guys. Love the podcast! Wish I could find a fishing podcast as good. Life would be perfect.I made the move to a Fuji Sprayer.  I bought one with the gravity feed gun but now think I made a mistake. I think it would be easier to hold finish in the cup between coats.What is your preference and why?Thanks so much. Joe
Hi Guys,
I recently asked a question concerning how to glue up a frame and panel so it’s flat. I took your advice and it worked great. Thanks so much!!!I have two unrelated questions:I recently purchased expensive hinges from Horton-brasses. When I received the hinges I made a jig out of MDF so I could simply rout out the mortises for the hinges to sit in. As usual, I make the jig so they are a perfect fit for the hing. I tested the jig on a piece of scrap and the hinge fit perfectly. I then used the jig on a cabinet I made and the hinge did not fit. I tried the various hinges I purchased and only one of the hinges fit (the hinge I used to make and test the jig). After measuring the hinges, I discovered that they were all different sizes varying by about .01”. I contacted Horton-brasses and explained the problem and they told me that their acceptable tolerance is +/- .05”. With some simple math this means that

Durable Kitchen Table, Hinge Wierdness, Sanding Slabs and MORE

This Episodes Questions:
Brian's Questions:
Hey guys I have a kinda lengthy question, so new to woodworking and I’ve been listening to your guys podcast and really like it!! Very helpful! Question #1 is it better to have a good table saw blade over a good saw #2 is it better to have a good table saw over a good incra fence!? Back story I have a delta table saw, I got for free from a friend, I was wondering if it’s worth spending the money or save and eventually get a better saw like a powermatic table saw etc.maybe I get caught up in the details of tools and expect them to do the work for me, but I am someone that like to have the right tools for the job. Granted as new as I am it’s hard to justify $10,000 to have all the right tools, just wondering if I should focus more on making something then, on the tools! Hope it all makes sense and it’s not more of a rant!! Thank you for all the work you guys do!! Ivan
I'm making a mantle for my living room out of rift-sawn white oak plywood. 74" long, with a miter fold design. My wife wants it to look the same way it does before applying finish, and I'm not sure how to do that or if it is even possible. I've tested with water-based poly (Minwax), but it causes it to look a bit "golden". Suggestions? Brian
Guy's Questions:
Hi fellas,Love the podcast and all your great advice.I recently glued up a free-standing (liquor) cabinet and was very nervous about it being square, especially since it was difficult to check for square (measuring corner to corner in the front and back) with all the various clamps on.  I ended up making the back panel (which fits into rabbets), which I knew was square, and placed it in the back (without glue) while the glue dried on the various joints (through tenons on top and bottom shelves, mid-shelves sit in stopped dados).  The idea was that if the square back panel fit correctly, it would help pull the whole cabinet into square. 
It turned out perfectly this time (wahoo!), but am not sure if I got lucky or if this is a reliable method to come back to.  What do y'all think?  Does this method make sense?  Any other suggestions on how to check or ensure square with free-standing cabinets of a decent size (46" tall, 26" wide, 16" deep)?Thanks, Bryan
Hi gents:  long time listener here and as I’ve said before, thanks so much for the great content you deliver.  You have discussed your spraying equipment set up in the past but I was hoping you could describe your spray BOOTH set up- obviously Brian is exempt from this question since he doesn’t apply finish.  How do you guys spray volatile finishes in the winter on your garage?  Do you have a spray booth like set up?  Do you openly spray in your garage workshops?  How do you vent potentially dangerous fumes?  Any details you can provide would be appreciated as I would like to do more spraying of shellac and I like wipe on poly both of which are challenges in winter time when you can’t work outside.Liam from Indianapolis
Huy's Questions:
I’ve recently found the podcast and am loving going back and learning from each episode! I’ve noticed that a ton of time has been dedicated to doling out wisdom on different types of finishing techniques and products. I’m sure the best way to learn all of this is through experience, but do you have and resources to recommend budding woodworkers as a go-to guide? With the way my brain works, learning the origins of each finish, their make-ups, and how that brings about their use cases and strengths/weaknesses would go a long way for me to internalize all of the various do’s and dont’s. Do you have a resource you go to when considering applicable finishing materials on a new project? Jeremiah
Love the show, I appreciate you guys giving it the time it takes to make it happen. My question is about a solid Walnut table that I built for my eat in kitchen. The material was 30yr + air dried Walnut milled down to a thickness of about 15/16" for the table top each board is six to eight

Water White Finish?, Gluing Up Square, Sagging Table Top and MORE!!

This Episodes Questions:
Brians Questions:
Hi guys! Love the podcast, as always. My question for you guys this time is about design. Specifically, it's about design based on that "special" piece of lumber. For example, I purchased a large piece of mahogany in the late 1990's to build electric guitars. I made two guitars from it and was left with a chunk of beautiful lumber that traveled with me for the next 25 years. Two years ago, I bought a mid-sized slab of black locust. I don't make "slab" furniture or use copious amounts of epoxy, so it'll end up getting cut up into a project.I know you guys normally design your projects and then buy the lumber, but have you ever bought (or acquired) that unique board and then had to design a project to do it justice? If so, what was the project? As a follow up question, what is the longest that you have ever owned a piece of lumber that you just couldn't get rid of?
Thanks,  Joshua from The Black Dog Woodworks.
I'm a new listener and your podcast has been a blast to listen to on my evening runs. I just finished a 3-year, gut-to-the-studs home renovation, and my 1 car garage was the renovation workshop. Now that the home is finished I am transitioning the shop into a proper woodworking space. During construction, I used a lot of 16D nails and 3" construction screws and tried to have a variety of fasteners on hand so I wouldn't be running to the hardware store 3 times a day.
This got me thinking. What are some common fasteners you like to keep in your shop? Any common screw sizes? Bolts? Washers? Nuts? Nails? Staples? It seems in woodworking shops that there's always a balance between having so many supplies that you'll never use most of them in 10 years to having so few supplies that you'll be running to the store 5 times a day. What is your approach to hardware consumables? Thanks for the great podcast. Adam
Guys Questions:
Really appreciate the podcast, i have been listening for about 18 months and am also working through your previous podcasts.   I am starting the dive into spray finishing. I have previously used wipe on or brush on finishes. I like shellac, but often coat with wipe on poly for extra protection. I would picture doing the same going forward.  Question: What are considerations/benefits to using a water based conversion varnish over wb poly?  What type of ppe is appropriate?  I have a relatively large shop which is climate controlled, not attached to house and can set up an area for finishing when needed, what type ventilation would be desirable for occasional finishing in this situation?  I build furniture and smaller items. Thanks,David at xcuse4tools custom woodwork    Hello everyone. Love the show. Great dynamic between you all and I really enjoy the lack of ego in the question answering. Your answers are efficient, helpful and easily digestible to a beginner woodworker.I recently acquired a Jessem Pocket Mill Pro for loose tenon joints. Like many, I had lusted after a Festool Domino but couldn’t justify the price tag for a hobby shop. The Pocket Mill Pro is a fraction of the cost and does everything I need it to do for my projects.The workstation that pairs with the pocket mill pro can also accept Jessem’s dowel jig. My question to you all is would a dowel jig even be necessary when I have the ability to make loose tenon joints already? Is there any advantage to adding the dowl jig to my arsenal or is it a waste of money when I already have the Pocket Mill Pro?Thanks in advance for any insight. Jason
Huys Questions:
I'm planning on making a face grain chess board.  I'll use 3/4" MDF as my core and glue the chess squares on top (grain from all squares facing same direction).  Chess squares will be about 1/8" thick.  I assume I'll also need to glue some 1/8" wood on the bottom to balance out the stresses.  I'll orient the bottom grain in the same direction as the top.  My question is, do I need to glue both sides at the same time, or can I glue one side, le

Episode 67 – Shellac Tips For Large Surfaces, Starting Clamp Collection, Break Down Workbench, & MUCH More!

Download our free app to listen on your phone