Support us on Patreon: https://www.patreon.com/woodshoplife

Sponsored by 3M Xtract

Guy

1) Thanks for the great podcast, I’ve learned a lot throughout the episodes. I’ve been a wood turner for twelve or so years but now getting into fine furniture making.  A shout out to Sean as I’m a fellow Kentuckian (Louisville).

My question is: I’m working on two shaker side tables right now that are 20”x20”.  As I think about the drawer construction, I’m at a bit of a crossroads with the bottom of the drawer. I could get high quality 1/4” plywood  for the drawer bottom and put the plywood in grooves. However, I don’t like the thought of putting plywood into my tables if I were to be honest. I’m sure it would be structurally fine and I wouldn’t have to worry about wood movement. However I’d like for the bottom to be made of poplar like the sides and back of the drawer. How do I make a drawer bottom from 4/4 lumber? My planer says I can’t plane anything thinner than 1/2” and I don’t have a drum sander. What is the best way to thin a board to 1/4” or 3/8” for a drawer bottom? I’d rather not use hand tools as I have arthritis in my hands. Is this a job for a planer sled?

Thanks much, John

My shop tools:

Router & table

Lathe

Drill press

Bench

Shaper

6” Jointer

13” planer

14” Bandsaw ( Jet Euro style)

Small Saw Stop (still alive!)

2) Hey guys! As always, I love the podcast, appreciate your individual takes on questions, and hearing about what's going on in your shops, except for Guy, he's too busy working to have anything going on in his own shop.

My question is about learning from your mistakes. Throughout your woodworking adventures, I'm sure you have all had that project that did not come out the way you had planned or expected. I recently found some very old woodworking projects that I made somewhere in the late 1990's. Instead of throwing them out, I put them in my shop to remind me of two things. Where I've come from, and what not to do. Do you guys have anything like this in your shops? What do you use to remind you to do better?

Thanks

Joshua from The Blackdog Woodworks

3) Hi guys, Thanks for the great, inspiring and sometimes intimidating podcast, because you guys are so good. I have a couple of questions. I have been asked to build a dining room table for my daughter. My first question is about design. The table will likely be a trestle style, made of walnut, a wood I have never worked before. The table will be about 6 feet long by 40" wide to fit into the space available. Is there a reason to glue the top along the long edge or along the short edge, or is this strictly or primarily an aesthetic decision? It seems like I would be likely to get a better edge to joint a 40" edge rather than a 60" edge. Second question if I can be presumptious, how do you keep focused on completing a project? It is always exciting to start a new project, but then as the time it takes stretches out, the endless sanding continues, the fear of applying a decent finish,  the excitement diminishes and I get to the point I just want to get it finished. Thanks again for the great information and terrific format.

Scott

Sean

1) Hello sirs.  Thank you for providing the best woodworking podcast bar none!  I am building a couple of side tables for my living room to go on either end of my couch.   I am using 8/4 walnut slabs for the table tops.  I'm wondering what kind of finish you would recommend for these slabs?  Bear in mind that I'm assuming my wife and children are not going to be too keen to reach for a coaster every time they want to put a glass of water down.  I prefer more of a matte finish, so don't really want to use epoxy or anything that's going to look like a layer of glass is sitting on top of the slab.  So what products

do you suggest to achieve maximum water protection without compromising a matte look?  And please include any specific application techniques, ie: number of coats, levels of sanding, etc.  Many thanks.   Keep up the amazing podcast!

2) Good evening, I'm Mason with blairswoodshop. Before I ask my question I just want to mention I love the podcast! It's awesome for my morning commute i think I'm about 80 episodes compete and look forward to more. Thank you guys for all the hard work on the podcast!  Just had a question for Sean. I see he has the performax 16-32, I just acquired a same style Jet 16-32. My question is if you have ever had issues with the conveyor belt tracking? I can't seem for the life of me to get it to track straight. No matter what I do it always tracks to the right, it has already took a chunk out of my brand new maveric abrasives conveyor belt. I know I'm not the only one with this issue, but no one seems to really have a fix. The only thing I've seen that might work is to buy a rubber conveyor belt which is upwards of 125$ plus shipping. Any help would be greatly appreciated! Thank you!

3) Good afternoon, good evening and good night gentlemen. Wanted to hear your preferred method of table top attachment to a base. (Z clips, figure 8s or oversized holes or any other method you can speak on that you prefer)

Paul