April 04, 2026

Which Drum Sander?, Drawer Slides, Door Repair and MORE!!!

43 minutes

Guys Questions:

I am going to be adding a 25/50 drum sander to my shop. I can’t afford a powermatic so it is between the Jet and Laguna Supermax. I went to AWFS this past year to see them in person and Jet was not at the show and Laguna only brought their large tools. I called one of the nationwide woodworking stores that sells both brands and asked the employee which he thought was better and his response was “ they are both great tools, but if you have a problem with either one of them Jet will take care of the problem immediately, and Laguna will eventually take care of it but it will take a while”. Laguna also charges a $199 shipping fee where as Jet does not. I would appreciate any advice on which one you would recommend.

I always look forward to listening to the podcast. Keep up the great work gentlemen! Tom

Hello Fellas

On my third round of listening to all your episodes. Thanks for all you contribute to the community. I am getting ready to move my shop from the garage to the basement. I want to keep the dust down to a minimum. I was looking at getting a Grizzly T10113 - Universal Overarm Blade Guard for Table Saws. Have you used or this or something similar. It is very pricey do you think it's worth the money. If not do you have any alternatives. Thank you and keep up the good work

Korey Griffin, Independence KY

When is a drawer too wide, specifically for under mount slides? I keep seeing these huge kitchen drawers that look to be almost 36-48" wide. How do they account for the large amount of weight that could potential be in these drawers. Do you guys have any experience using the blum tandem stabilization bars? They state they can be used up to 53" but that seems widely wide. How would you go about building drawers that are over 36" wide? Jesse

Huys Question:

Hi Woodshop Life Podcast Team,

Thanks for all the great content—new woodworker here (not a cheap hobby by any means and I mostly blame you guys for this), I went in deep with about 50K in tools but so worth it as I love the idea of building things for people that they will have when I'm gone. I'm a Power Engineer by trade, and I learn a ton from the podcast.

Quick question: I’m in Sylvan Lake, Alberta (-40C to +35C weather) and store a decent hardwood stockpile (Walnut, Wenge, Maple/Figured Maple, Zebrawood, Rose Woods—kiln-dried from a reputable Calgary seller) in a 14’ x 10’ room in the back of my heated oversized 3-car garage. Winter RH is usually ~22–25% and summer can swing much higher. I could add a small humidifier in the storage room but that's about it. Storage room has air flow, in floor heat and wood is sitting off the concrete stored vertical on ends. Whole home humidity control is hard to achieve in Alberta without creating a lot of condensation on the windows in winter months which is not good. So we just except the cracked bleeding skin during the winter months.

Would you leave it alone and accept seasonal humidity movement, or try to hold the storage room around ~35% RH? If you would control it, what’s a practical target range? Part B - Is cutting wood stored at 22% RH a good idea - I assume it will swell so much in the summer months and assume 22% is way to low to store wood long term over a couple years.

Thanks for the wicked podcast - I'd love to come on, I'd have so many questions during each show.

Thanks!

Trenton (Sylvan Lake, AB

I started a stripping project of my redwood door. It’s old old old! So I am trying to be thoughtful of the contours and the soft wood. I need some guidance since the paint is fighting me and Ive kind of hit a wall. Ian

I have another closet door that my kids have forcebly pulled the screws from the hinge. Not sure how to approach fixing the holes for screws other than cutting a chunk out of the door and glueing and sanding a new piece in. Any thoughts would be helpful. Ian

...more