
Sign up to save your podcasts
Or


Part 1 of building your own Steampunk Goggles revision 2.
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
For full show notes, visit https://twit.tv/shows/know-how/episodes/304
Protect yourself with MFA, encrypted messaging apps, and surf anonymously with the TOR browser.
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
Guest: Nathan Olivarez-Giles
For full show notes, visit https://twit.tv/shows/know-how/episodes/303
Revision 2 of the Steampunk Goggles project has improved comfort, strength and a stealthy cartridge system upgrade!
Parts
Vintage Steampunk Goggles ~$8
Triple Lens Loupe ~$7
Steampunk Gears ~$7
16 LED WS2812 Ring ($4 x2) ~$8
Arduino Nano ~$3
10k Rotary Potentiometer (Pack of 10 - You only need one)) ~$3
Female Walkery Battery Connector ~$2
30 AWG silicone wiring (Red/Black/White) ~$2
Total: $40.00
3D Parts
1. Right Frame piece [Steampunk_v2_RightFrame]
1. Left Frame piece [Steampunk_v2_LeftFrame]
2. LED Ring Holder (x2) [Steampunk_v2_LEDRingHolder]
3. Bridge Segments (x2) [Steampunk_v2_Bridge]
4. Right Cartridge [Steampunk_v2_CartA1]
5. Left Cartridge [Steampunk_v2_CartB1]
6. Cartridge Door (x2) [Steampunk_v2_Door]
7. Potentiometer Flange [Steampunk_v2_PotFlange]
Tools
1. 3D Printer
2. Soldering Kit
3. Dremel Tool
4. Hot Glue Gun
The code and STL files can be found at the following HERE
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
Connect with us!
Thanks to CacheFly for the bandwidth for this show.
Set up your own RaspPi TOR AP!
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
For full show notes, visit https://twit.tv/shows/know-how/episodes/301
Screens and buttons are nice, but it's time to add network capabilities to our Arduino projects. We're going to use an Ethernet shield with an Arduino UNO to build a few basic network-enabled gadgets.
Parts
Geek credit UNO R3 ATmega 328P Dev Board ~$4
Geek credit Ethernet Shield Module W5100 MicroSD ~$6
- or -
W5100 Ethernet Shield R3 (PoE) ~$10
Basics
* There are examples of Ethernet projects build into the Sketch IDE
Ethernet Server with Analog Input
Code Example: _01_WebServer
* Code for this example is under "File - > Examples -> Ethernet -> WebServer"
* We need to change the following in the code:
-- Set the IPAddress to "192.168.0.229"
-- Change the "for" loop so there are only 2 Analog reads
* We need to wire the following:
-- Power to the outer POT pins
-- Center pins to A0 and A1
** Play with the "Refresh" setting to show a quicker refresh
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
Connect with us!
Thanks to CacheFly for the bandwidth for this show.
We answer questions from our G+ group! How to balance a quad copter, second monitor recommendations, radio-controlled switch, and how much light is too much for your indoor grow!
Balancing Quads
-- Mr. ROKnBOK
"Has the subject of "balancing the quadcopter" been addressed on KnowHow? If so, please point me to that episode. Thanks, KitAs!"
I need a 2nd Monitor!
-- Daniel Casciato
"Padre mentioned on Windows Weekly episode 471 that one of his best tech purchases was a portable accessory screen for his laptop. This allowed him to use a dual screen setup on the go. 2 questions... 1) what is this screen? 2) Can it be used with a stylus for digital notes, specifically as an input for OneNote?"
Asus MB169C+ ~$150
* 15.6"
* Full HD
* 1920x1080
* IPS
* USB-C ONLY!
Asus MB169V+ ~$190
* Same Specs
* No IPS, USB 3.0
Throw a switch with a RC
-- Wayne Hobbins
"""I'm trying to figure out a way to close a connection with my RC TX using a spare channel that's not passing any electricity like 5 or 12 volts. I know how to do this with a servo and a mechanical switch, but there must be another way.
I thought that the Turnigy transmitter controlled switch might work, but apparently it needs a voltage on one wire to make the connection. I checked the red wires using a ohm meter and there was no difference when switched on and off.
Any ideas?"
We're using an Arduino!
* We're going to use the same setup that we used for the Growduino
* The Arduino will read the PWM value from the receiver, then energizer or de-energize the relay
1. Wire it:
- Arduino 5V to the receiver
- receiver signal to pin 8 of the arduino
- relay ground to ground
- relay positive to pin 7 of the arduino
- circuit through the relay switch pins
2. Program it:
- Use (pulseIn) to read the receiver data value
- Use an if-else to turn on/off the relay
Demo:
1. Assemble circuit
2. Display PWM values from Arduino
3. Show if-else logic
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
Connect with us!
Thanks to CacheFly for the bandwidth for this show.
Program and attach an OLED i2C to your Arduino project!
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
For full show notes, visit https://twit.tv/shows/know-how/episodes/298
What is a switch, Address Resolution Protocol, and the right hardware for you!
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
For full show notes, visit https://twit.tv/shows/know-how/episodes/297
Writing to digital pins, reading from digital pins, and how to use i2c RTC with an i2c LED Screen.
RTC
An Arduino's memory is wiped when it loses power. For most of our projects, that doesn't matter b/c we're only using the Arduino as a momentary I/O controller. However, when we have a project that needs to be persistent, we need a way to keep time even when the Arduino is powered off.
Segment Summary:
We're going to connect a Tiny RTC to an Arduino.
Parts:
1. Tiny RTC I2C DS1307 Real Time Clock $2.00
2. Arduino
3. Jumper Wires
What is I2C?
* I2C (Pronounced "I Squared C") can communicate with multiple devices over short distances with just two wires: SDA (Data Line) & SCL (Clock Line)
* Technically, it's a "Multi-Master, Multi-Slave, Single-Ended, Serial bus"
You need to know what are the SCL and SDA pins on your arduino
* Uno, Nano or clone (SDA = A4 // SCL = A5)
* Mega (SDA = 20 // SCL = 21)
* Leonardo (SDA = 2 // SCL = 3)
* Due (SDA = 20 // SCL = 21)
Geekcreit i2c 20x4 LCD Display $6
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
Connect with us!
Thanks to CacheFly for the bandwidth for this show.
Ports, DMZ, Forwarding, and NMAP!
Hosts: Fr. Robert Ballecer, SJ and Bryan Burnett
For full show notes, visit https://twit.tv/shows/know-how/episodes/295
From the publisher's feed
Get your gaming on! Jason Howell and Ars Technica's Sam Machkovech bring you 12 episodes and cover it all, from tips and tricks, consoles, gaming rigs, controllers, Virtual Reality, classic gaming, live gameplay, mobile gaming, console hacking, and more! Plus, they'll wrap up with a holiday game guide.
Although the show is no longer in production, you can enjoy episodes from the TWiT Archives.

9 Listeners

34 Listeners

109 Listeners

6 Listeners

139 Listeners

29 Listeners

96 Listeners

35 Listeners

72 Listeners

116 Listeners

94 Listeners

24 Listeners

50 Listeners

15 Listeners

10 Listeners

9 Listeners

0 Listeners

28 Listeners

31 Listeners

0 Listeners